B Square Infra Solutions

• Fibre reinforced - strong adhesion to surface.
• Better hiding & better wall finish. 
• Good water resistance.
• Flexible
• Non-shrink – one time application. 
• Bonds strongly to cementitious substrates. 
• Better water resistance

• Pioneering the technology in India
• UV Resistant & Foot trafficable
• Zero dilution ensures uniform film thickness
• No breaking of roofs
• 3 Coat system in 3 different colors
• 1 mm film thickness

• Damproofing treatment for RCC water tanks. Internal damp wall treatment.
• As putty with OPC- White cement to fill the fine cracks of internal walls.
•  In sterile areas of pharma, food industries & hatcheries etc.

• Application advantage - It can be applied over damp concrete & plaster surfaces and provides excellent water resistant coating with tough & hard film.
• Microbial resistant - Possesses anti-fungal property and is resistant to micro-organisms. Adhesion - Provides excellent adhesion to all cementitious substrates.
• Chemical resistant - Excellent resistance to water, salt water, mild acids, alkalis & soap water.
• Toxicity – It is Non-toxic.
•  Eco-friendly - Non-hazardous and non-flammable.
•  Economical - Water dilutable with high coverage hence economical.
• CFTRI Certified - Safe for drinking / Potable water contact.

• Styrene Butadiene co-polymer latex liquid that improves waterproofing
• Strengthens bonding of new and old concrete & plaster
• Enhances strength & water resistance of repair mix - concrete & mortar

• Proper slope must be maintained on flat rooftops to prevent any water accumulation.
• Substrate MUST be in SSD condition before application of primer.
• All joints should be coved by an angular fillet.
• Parapet walls should also be coated with weberdry ACR seal, to give a seamless waterproof coat.
• All corners, gaps, joints, protrusions etc shall be reinforced by webertape stickon, and an extra coat should be applied.
• Make sure the applied coats do not get wet before complete curing.
• Do not make any structural changes to the applied surface as this may lead to puncture of the coating system and the system would have to be laid again.

• Delays Corrosion - Makes concrete more cohesive, hence protects steel better against corrosion.
• Improves workability with M-Sand - Facilitates easy placing and good compaction of mixed cement concrete and plaster mortar/ screed specially made with M-Sand.
• Waterproof concrete & mortar - Increases durability by improving the waterproofing of concrete.
• Increase strength and durability - The setting time and compressive strength of the concrete remains within the specification limits.
• Compatibility - Being a liquid, easily dispersible & compatible with concrete/mortar mixes.
• Shrinkage - Reduces shrinkage crack development in plaster & concrete.

• Bonding - Good binding of chalky or porous substrates and over coating. 
• Suitability - Used as a primer on internal and external surfaces.
• Alkali resistant - Based on chemically inert polymers hence suitable for high alkaline substrates. Penetration - Provides deep penetration thus imparts excellent substrate adhesion.
• Efflorescence - Provides excellent efflorescence resistance due to its chemical inertness.

• Dilute Dr. Fixit Primeseal with water in proportion of 2:1 and stir well until a uniform consistency is achieved.
• Apply a single coat of diluted Dr. Fixit Primeseal on the cleaned substrate & allow it to dry for 2 to 3 hours before commencing to further finish coats.
• Light cut with sand paper the coating of Dr. Fixit Primeseal before commencing the finish coats on internal walls Precautions & Limitations
• Only 50% dilution is recommended for Dr. Fixit Primeseal by water.
• Excess water on substrate must be removed by suitable means.
• Do not apply during rains or in direct sunlight.
• Do not tint the primer

• Effective bonding with substrate
• Can be used for Internal walls, External walls and Roofs
• Penetrates the Cementitious substrate
• Efflorescence resistant Primer
•  Effective bonding with Substrate
• Efflorescence Resistant Penetrating Primer

• Mix thoroughly, so as to not have any lumps, and ensuring webertec sbr litX is evenly distributed throughout the mix.
• Where water and webertec sbr litX both are required, mix water and webertec sbr litX in a bucket and add to a mix of sand and cement as per the mixing ratio.

• It provides an excellent bond to the existing substrate.
• It makes the structure impermeable to liquids.
• It improves flexial strength and hence avoids cracking.
• Shrinkage cracks are reduced.
• Thnner screeds can be cast for similar strengths, reducing weight and material used.
• It has excellent slip resistance when used for flooring scrreds.

• Clean the substrate of oil stains and bond inhibiting compounds. Also remove dirt, dust and laitance, if any, using a high-pressure water jet or any other suitable method.
• Corroded reinforcement bars should be exposed around their full circumference, should then be cleaned to remove all the loose particles and should be treated with an anti-corrosive product.

Additional Information:

• Packaging Details: Glass fiber mesh for Waterproofing, Plastering, Construction. It comes with 1m x 50m roll.